Home>Bearing knowledge>Compressor bearing overheating cause and sweep |
Compressor bearing overheating cause and sweep
/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
1. The bearing and the journal are not evenly attached or the contact surface is over. ㄅ浜霞湎豆. The ノ ノ ノ 谋 谋 妊 妊 妊 妊 妊 妊 ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( 2. The bearing is skewed or the crankshaft is tortuous and distorted.
3, the quality of the bearing bush is not good; the quality of the lubricating oil does not match (viscosity. Change the venting of the chlorine. The oil pressure of the gear oil pump is too low; and the oil supply is suspended; the bearing bush is short of oil;
4. There are too many impurities or lubricating oil in the bearing; or the lubricating oil is too dirty.
5. The bearing bush has uneven wear and tear.
6. When the compressor is installed, the spindle and the motor (or diesel) spindle coupling are not aligned; the error is too large; the two axes are skewed.
Cleaning method:
1. Scrape the bearing bush with the coloring method; make the contact surface meet the demand; improve the specific pressure per unit area,
2, properly adjust the cooperation gap; view the crankshaft twists and turns, distortion status; change the new crankshaft or repair according to the situation,
3. Use the bearing bush that fits the quality; view the oil pipeline and the gear oil pump; use the lubricating oil that meets the quality requirements; check and adjust the oil pump to make the pressure reach the demand.
4. Remove and replace the new engine oil; adjust the oil pressure,
5. Replace the new bearing bush,
6, the two machines concentricity should be positive, leveling its public service value should match the value of the machine manual rules. Especially when the compressor and motor are connected with rigid connection; more attention should be paid to alignment.
Recommend to friends comments close window
Bearing related knowledge |
Grinding of "imported bearing ring double end" Analysis of the Causes of Failure of TB Aircraft Landing Gear Wheel Bearings: Reasons for Failure of FAG Bearings Replacement of Lower Support Bearings of Door Machines by Lifting Method (2) Common equipment for bearing ring casting (1) |
This article links to http://
Please indicate the bearing network http://
Previous:Skills demand for sliding bearing scraping Next: Unique axial positioning of bearings
Round Dot Rubber Sheet
Parameters: specific gravity: 1.4-1.7g/cm; breaking tenacity: 3-5Mpa; elongation:200-300%; hardness: 70 ±5°
Performance: temperature range: -20℃-70℃. good elasticity. wear resistance, waterproof and anti skid, effective anti corrosion;
Usage: this kind of products can be widely used for laying and decoration of tables, floor and paths in hotels, sports facilities, conference halls, airports, ports, ships,vehicles, etc.
Color: black, gray, brown, blue
Product name |
Colour |
Product standard |
Usage and property |
Black,red,blue, grey,green |
GB/T5574-2008 |
Hardness:low middle high Pressure:1.6~6.0Mpa The allowed temperature:min-35℃ max +60℃ Medium:air or water Usage:Punching washer/gasket ring /seal of the door window. |
|
Acid-resisting Rubber Sheet Alkali-resisting Rubber Sheet |
Black,red,blue, grey,green |
GB/T5574-2008 |
Hardness:low middle high Medium:acidity liquid alkallnity liquid Function:acid-resisting alkali-resisting The allowed temperature:min-35℃ max +60℃ Usage:making all kinds of gasket ring/washer bedding equipment or surface. |
Oil-resisting Rubber Sheet |
Black,red,blue, grey,green |
GB/T5574-2008 |
Hardness:high Medium:engine oil,gasoline,lubriacting oil,transformer oil etc. Function:oil-resisting The allowed temperature:min-30℃ max +100℃ Usage:punching washer/gasket ring bedding surface of equipment. |
Heat-resisting Rubber Sheet |
Black,red,blue, grey,green |
GB/T5574-2008 |
Hardness:low middle high Medium:steam,air,hot air Function:heat-resisting,aging-resisting The allowed temperature:min100℃ max 250℃ Usage:punching all kinds of gasket ring/washer/gasket/board |
Insulation Rubber Sheet |
Black,red,blue, grey,green |
GB/T5574-2008 |
Hardness:low middle high Function:prevent electricity/static electriaty. The allowed voltage:max 50,000kv Usage:This products is suitable for use in electriaty,oil chemistry,metallurgy,communication etc(spreading surface of punching all kinds of gasket ring/washer/boards) |
Round Dot Rubber Sheet,Round Dot Rubber Floor,Round Button Rubber Sheet,Rubber Sheet With Round Button
HEBEI HENGDA SEALING MATERIALS CO.,LTD. , http://www.hengdasealing.com