Construction machinery hydraulic piston pump use and maintenance

In this paper, direct-axis swash plate piston pump-based, describes its use and maintenance methods. A hydraulic pump oil supply form Direct-axis swash plate piston pump is divided into two types of self-suction oil pressure type. Most of the pressure supply type hydraulic pump with air pressure tank, there are hydraulic pump itself with a charge pump to the hydraulic pump inlet to provide pressure oil. Self-priming oil pump self-priming oil capacity, no external oil supply. By hydraulic pressure oil tank, each time you start the machine, you must wait for the hydraulic pressure box to reach the use of air pressure before operating machinery. If the pressure of the hydraulic tank is low, it will cause the pull-off phenomenon in the hydraulic pump and the slippery whip, which will cause the abnormal wear of the return plate and the pressure plate in the pump body. The use of charge pump piston pump, use 3000h, the operator needs to check the plunger pump 1-2 times a day to check the hydraulic pump running sound is normal. If you find the hydraulic cylinder speed or boring car, you should disassemble the charge pump check, check the edge of the impeller scratches, internal gear pump clearance is too large. For self-priming piston pumps, the fluid in the hydraulic tank should not be lower than the lower limit of the oil standard, and a sufficient amount of hydraulic oil should be maintained. The higher the cleanliness of the hydraulic fluid, the longer the life of the hydraulic pump. 2 hydraulic pump bearing plunger pump is the most important part of the bearing, if the bearing appears clearance, you can not guarantee that the hydraulic pump within the three pairs of normal friction pair, but also undermine the friction of the hydrostatic bearing oil film thickness, lower Piston pump bearing service life. According to information provided by the hydraulic pump manufacturer, bearing the average service life of 10000h, more than this value will need to replace the new port. Demolition of the bearings, there is no professional testing equipment can not detect the bearing clearance, only visual inspection, such as the roller surface scratches or discoloration, it must be replaced. In the replacement of bearings, bearings should pay attention to the original letters and models, most of the piston pump bearing load capacity of large bearings, it is best to buy the original manufacturer, the original specifications of the product, if the replacement of another brand, should consult the bearing experience Staff look-up table swap, the purpose is to maintain the bearing accuracy level and load capacity. 3 pairs of friction pair inspection and repair 3.1 Plunger rod and cylinder bore Table 1 for the replacement of the plunger pump parts, when listed in the table various types of clearance overweight, can be repaired as follows: (1) Cylinder lining copper sleeve, copper sleeve can be replaced by the method of repair. First set a set of plunger rod diameter trim to a uniform size, and then over 1000 # polished sandpaper outside diameter. Cylinder installation copper sleeve of three ways: (a) cylinder warm or copper sleeve low temperature cryogenic extrusion, interference assembly; (b) mining with Loctite adhesive assembly, which method we require copper jacket Diameter surface of the groove; (c) cylinder tapping, copper outer diameter of the thread, Tu Le Ta plastic, screw into the assembly. (2) The cylinder and the copper sleeve fused by means of sintering are as follows: (a) grind and repair the cylinder hole by using a grinding rod, manual or mechanical method; (b) re-boring the cylinder bore by using a coordinate boring machine; (c Reamer cylinder bore repair. (3) adopt "surface engineering technology", the method is as follows: (a) electroplating technology: a layer of hard chrome plating on the plunger surface; (b) electroplating technology: brushing wear- Thermal spraying or arc spraying or electrospraying: spraying high-carbon martensite wear-resistant material; (d) laser welding: welding high hardness wear-resistant alloy powder on the plunger surface. (4) Cylinder hole copper-free sleeve cylinder material is mostly ductile iron, the cylinder wall to prepare amorphous film or coating. Because of this special material on the inner wall of the cylinder bore, it is possible to form a hard-hard paired friction pair. If you blindly grind the cylinder bore, the surface material inside the bore of the cylinder bore is removed and the more structural properties of the friction change. Was removed coating friction pair, if forced to use, the friction surface temperature will rise sharply, the plunger rod and cylinder bore gluing. In addition to the surface of the plunger rod to prepare a unique film coating, the coating contains anti-wear + wear + lubrication function, this group of friction actually hard or soft match, once people change the coating, it will destroy the most Good matching pair of friction materials, repair these special piston pump, it is necessary to send a professional repair shop. 3.2 Slipper and Swashplate Swashplate and Swashplate friction are the most complex pairs of swashplate piston pumps in three pairs. Table 1 lists the plunger rod ball head and the ball socket of the gap, if the gap between the plunger and the slipper, high pressure oil in the plunger chamber will leak from the gap between the ball and the sliding head of the plunger, slip Shoe and swash plate thinning, severe hydrostatic pressure support will cause failure, slipper and swash plate metal contact friction, slipper ablation off, plunger ball head scratched swashplate. Plunger rod ball head and sliding ball socket beyond the tolerance 1.5 times, it must be replaced in groups. Plunger rod and cylinder bore Plunger rod diameter φ16φ20φ25φ30φ35φ40 Standard clearance 0.0150.0250.0250.0300.0350.040 Limit clearance 0.0400.0500.0600.0700.0800.090 Standard clearance 0.0100.0100.0150.0150.0200.020 Piston rod Ball head and sliding ball socket Ultimate clearance 0.300.300.300.350.350.35 swashplate effect After a period of time, the swashplate surface will appear concave phenomenon, before using the platform grinding, we should first measure the original size and plane hardness. Grinding, and then measure the amount of grinding is, such as within 0.18 plunger pump use without interference; if more than 0.2mm above, you should use nitriding method to maintain the thickness of the original nitride layer. When the swash plate plane is scraped out of the groove by the plunger ball head, the method of laser alloy powder can be used for repairing. Laser cladding technology can not only ensure the bonding strength of the material, but also ensure the hardness of the filler material, and does not reduce the hardness of the surrounding tissue. Also Shun to adopt chromium welding rod for manual surfacing, welding of the swash plate plane to be re-heat treatment, the best nitriding furnace heat treatment. Regardless of the method used to repair the swashplate, you must restore the original dimensional accuracy, hardness and surface roughness. 3.3 with the flow plate and the cylinder with the repair of the distribution surface The distribution plate with a plane with the flow and spherical with the two forms. Spherical with the flow of friction pair, the cylinder with flow surface scratches relatively shallow, by means of grinding repair; cylinder with flow grooves deep, should first use "surface engineering" means to fill the trench, and then grinding , Can not be blind grinding, to prevent copper thinning or leakage of steel base. Friction pair in the form of plane flow can be grinded on the platform with high accuracy. Before the grinding of the cylinder body and the valve plate, the total thickness dimension and the size that should be ground off should be measured before compensation to the adjusting mat. With a larger flow plate, the grinding should be re-heat treatment to ensure the hardened layer hardness (see Table 2). Table 2 Piston Pump Parts Hardness Standard Plunger Rod Recommended Hardware HS84 Plunger Rod End Recommended Hardness> HS90 Recommended Hardness of Swashplate Surfaces> HS90 Recommended Hardness of Disc Hoods> HS90 Cylinders and Discs may be repaired using the following method With the surface of the leakage situation, that is, in the distribution plate coated with Vaseline oil, the drainage block blocked, painted with oil flow plate flat on the platform or flat glass, and then the cylinder on the plate with the allocation in the cylinder hole Into the diesel fuel injection interval, that is, a hole oil, a hole without oil, observe 4h above, the plunger hole no leakage and collusion of diesel, indicating that the cylinder with the flow plate grinding qualified. 4 Conclusion piston pump service life, and peacetime maintenance, the quantity and quality of hydraulic oil, oil cleanliness and so on. Avoid oil particles in the piston pump friction caused by wear and tear, but also to extend the effective life of the plunger pump. In the maintenance of replacement parts should try to use the original production of parts, these parts sometimes fake parts than other expensive, but the quality and stability is better, if the purchase of counterfeit parts cheaper prices in the short term seems to be saving costs, However, this poses a hidden danger, may also cause greater damage to the use of the plunger pump.