Hydropower acceptance |
Acceptance project | |
1 | Pressure test: Newly installed water supply pipes, metal and plastic pipes and their joints. (tested by the manufacturer) |
2 | Inter-pipe spacing: The water supply pipe and the gas pipe are laid in parallel (the intersection is less than or equal to 10mm, and the parallel is less than or equal to 50mm). |
3 | Pipeline installation: The hot water pipe should be on the left side of the cold water pipe and keep the space between the hot and cold water pipes. |
4 | Metal hot water pipe for heat treatment. |
5 | Overload short circuit, leakage protection: air conditioning, kitchen, bathroom power outlets, other power outlets and lighting power supply design is reasonable. Each point circuit breaker must have overload and short circuit protection |
6 | Indoor cabling: Indoor threading should be done by pipe laying (except that the top surface of the cast-in-place concrete floor can be sheathed). A well-insulated single-stranded copper wire should be used, and the wires in the tube can be twitched. All kinds of wires shall be piped separately (different loops, voltage classes or AC-DC wires shall not be worn in the same pipe). |
7 | Insulation resistance grounding protection should be reliable. |
8 | Electrical piping junction box: The use of open coating, the electrical tube may not be fixed on the boom or keel. The lamp head and junction box should be set up for easy maintenance, and the cover plate should be connected to the lamp position with a hose. Fixture connection should be fixed, it is forbidden to use wooden mallets to fix, all kinds of conductors must not be naked. |
9 | Electrical switch, socket and gas pipe spacing (less than or equal to 150mm) meet the specification. |
10 | Line tube spacing: The distance between the wire and gas pipe and water pipe is reasonable and in line with the specification. |
Remarks: shaking table, weak light pen. |
Mudwood acceptance |
Acceptance project | |
1 | The plastering surface of the wall is smooth, the facade is vertical, and the square of yin and yang is square. |
2 | Plastering should be carried out in layers. Flat tops and facades should be clean, smooth and straight, with straight corners, and firm, void-free drums, delamination, ash and cracks. Significant measures to prevent cracking should be taken from plastering at the basic interface of different materials. |
3 | Tile inlaid: smooth surface, vertical facade, square yin and yang. |
4 | The seam width is the same, and the drainage slope of the floor tiles meets the drainage requirements. |
5 | Firmly attached to the surface, the surface is smooth and clean, no leaks, uniform gaps, straight and plump joints, the surrounding straight, brick surface without cracks, drop angle, lack of defects and so on. |
6 | Door and window installation: strong installation, flexible opening, tight shut-off, no rebound fallback, no self-opening and self-closing phenomenon. In a pipe). |
7 | The appearance of doors and windows: The surface should be smooth, no planing marks, no degumming and worms. |
8 | Door and window accessories: Doors and windows should be complete accessories, the correct location, and securely installed. |
9 | The vertical side is vertical. |
10 | The frame and the fan, the fan and the fan seam are flat. Door and window fan small seam. |
11 | The inside of the door and window cover is straight. Small seams. |
12 | Decorative plate: The surface should be smooth, with uniform wood grain orientation, tight joints, smooth edges and edges, no burrs or flash edges, and even width of decorative gaps between layouts. The veneer is firmly installed with no significant deviation along the line and the yin and yang angles are vertical. |
13 | Ceiling: Installed firmly, flat surface, no bending misalignment. Wooden keel should be brushed fire, anti-corrosion coating. |
14 | Ceiling: The joints have small errors at both ends. The level of seams is flat. The partition panel is vertical and vertical. Separator yin and yang angle Founder. |
15 | The frame and the fan, the fan and the fan seam are flat. Door and window fan small seam. |
Paint acceptance |
Acceptance project | |
1 | Painted wood grain is clear, brown eyes are smooth, smooth and even. |
2 | The paint surface is free from cocoon, falling, wrinkled skin, and no small surface. . |
3 | The paint color is basically the same, no brushing, no peeling. |
4 | The paint shall not be allowed to leak brush, bubbling, peeling, marking, or rust. |
5 | The surface of the wall paint has no peeling, shelling, bubbling, color difference, pan-alkali, pan-color, no blistering, falling, particles and so on. |
6 | The wall surface is evenly coated with firm bonding, with no leakage coating (mirror mirror) and powder dropping. |
7 | The deviation of the wall color line is small. |
Completion acceptance |
Acceptance project | |
1 | The floor surface is flat, the gap width is the same, and the seams are flat. |
2 | There is no floor warping in the main common area of ​​the floor. |
3 | There should be no looseness in the laying of the floor, and expansion joints should be left between the wall and the wall. There is no obvious sound when walking. |
4 | Appearance: The surface of the floor should be clean and free of dirt, wear marks, burrs, etc. Wooden joists are firmly installed. |
5 | Skirting board: The joints are tight, flat, and the top corner line is straight. |
6 | Appearance of sanitary ware: The watch should be clean, non-damaged and firm. |
7 | Faucet, valve, water meter: open flexible, normal operation, open water, left hot right cold, no leakage of water seepage phenomenon. |
8 | Bathtub: After the installation is completed, the water test should be completed within 1/3 and 2h. Spillway Irrigation Test No Leakage |
9 | Basins, sinks: securely mounted, filled with water to the overflow, 2h water test should be no leakage |
10 | Toilet: fixed, smooth, no leakage |
11 | The shower room: The base is free of stagnant water, the drain pipe is connected by a hard pipe, and the glass of the shower room should be made of safety glass, and there is no leakage phenomenon in the joint with the wall. |
12 | Electrical equipment: The installation location meets the standards, and the materials are reasonable and convenient to use. |
Construction Acceptance Window Painted Sockets Glass Appliances Floor Tiles Glass Tiles Glass Doors Kitchen Glass Sliding Doors Bathroom Tiles Bathroom Doors Bathroom Tiles Colors Bathroom Ceilings Materials Bathrooms Ceilings Toilet Designs Bathroom Tiles Bathroom Leaks Public Toilet Tiles Rubber Floor Tiles Kitchen Tiles
Huaxiajie Macromolecule Building Material Co., Ltd. , http://www.zjpvcpanels.com